Did some jobs on the TF today.
Moderators: Jo from Somerset, nigelandjo
- Madgasters
- Posts: 239
- Joined: Sun Nov 25, 2007 10:51 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: BGTV8 TF135 ZTTCDTI
- Contact:
Did some jobs on the TF today.
As we had the day off today me and Hollie spent a bit of time on the TF.
First we put some aluminium grilles in the boot vents, which I wasn't sure of at first but now I have done them I like them alot. Then I did the same in the side vents, and whilst I had the side vent out on the LH side I re-routed the cold air feed to the K & N filter. Then we painted all four calipers red and cleaned up the inside of the wheels. Last of all we changed all the interior bulbs to Leds.
First we put some aluminium grilles in the boot vents, which I wasn't sure of at first but now I have done them I like them alot. Then I did the same in the side vents, and whilst I had the side vent out on the LH side I re-routed the cold air feed to the K & N filter. Then we painted all four calipers red and cleaned up the inside of the wheels. Last of all we changed all the interior bulbs to Leds.
- Madgasters
- Posts: 239
- Joined: Sun Nov 25, 2007 10:51 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: BGTV8 TF135 ZTTCDTI
- Contact:
- stux99
- Posts: 2614
- Joined: Mon Oct 08, 2007 5:18 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: TF/TF Steppy/MGGS/3
- Location: Somerset/Dorset border
Re: Did some jobs on the TF today.
Looks good.A job well done
I was also busy at the weekend, more about that later.
New wheels?
I was also busy at the weekend, more about that later.
New wheels?
- James Curgenven
- Posts: 1695
- Joined: Wed Sep 26, 2007 9:45 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: MG ZT 260 SE #455
- Location: Minehead
- Contact:
Re: Did some jobs on the TF today.
I hope you used some wheel sealant while you had them off and cleaned, as it makes getting the brake dust off so much easier!
- colintf
- Committee Member & Regional Rep
- Posts: 12489
- Joined: Thu Oct 04, 2007 5:49 pm
- MGF Register Region: Devon & Cornwall
- Model of Car: MG PA TF160 ZTV8
- Location: Bristol / Cornwall (back home!)
- Contact:
Re: Did some jobs on the TF today.
looks good
Colin Murrell
MGF Register International Liaison Rep
MGF Register Regional Rep for Devon & Cornwall and Cotswold Regions
MGCC Z and V8 Registers Reps for V8 ZT'/ZTTs
http://www.two-sixties.com/main.htm http://www.triple-mracing.com/
- nellyandjoo
- Posts: 789
- Joined: Mon Oct 08, 2007 9:27 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: MGTF 135
- Location: Bower Hinton
Re: Did some jobs on the TF today.
TF looks good. Can't wait to see it in the flesh! (so to speak)
Mid Life Crisis
- nigelandjo
- Committee Member & Regional Rep
- Posts: 4915
- Joined: Tue Oct 09, 2007 9:44 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: TF85th,TF135,Trophy
- Location: Berrow
- Contact:
Re: Did some jobs on the TF today.
Paul / Hollie, looks like a good days work! We'll look forward to having a closer inspection at the next meeting!
Nigel
Nigel
Nigel May
Somerset & Dorset Regional Rep, Membership Secretary, Registrar & Archivist
Email: somerset.dorset@mgfregister.org members@mgfregister.org
MGCC Members register here: https://mgfregister.org/?page_id=319
Somerset & Dorset Regional Rep, Membership Secretary, Registrar & Archivist
Email: somerset.dorset@mgfregister.org members@mgfregister.org
MGCC Members register here: https://mgfregister.org/?page_id=319
- colintf
- Committee Member & Regional Rep
- Posts: 12489
- Joined: Thu Oct 04, 2007 5:49 pm
- MGF Register Region: Devon & Cornwall
- Model of Car: MG PA TF160 ZTV8
- Location: Bristol / Cornwall (back home!)
- Contact:
Re: Did some jobs on the TF today.
assuming its not DARK alreadynigelandjo wrote:Paul / Hollie, looks like a good days work! We'll look forward to having a closer inspection at the next meeting!
Nigel
Colin Murrell
MGF Register International Liaison Rep
MGF Register Regional Rep for Devon & Cornwall and Cotswold Regions
MGCC Z and V8 Registers Reps for V8 ZT'/ZTTs
http://www.two-sixties.com/main.htm http://www.triple-mracing.com/
- nigelandjo
- Committee Member & Regional Rep
- Posts: 4915
- Joined: Tue Oct 09, 2007 9:44 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: TF85th,TF135,Trophy
- Location: Berrow
- Contact:
Re: Did some jobs on the TF today.
Well not on the TF, but I did take the F to the local tyre fitting centre to have new wheels fitted:
Anybody want a set of well kerbed 16" 6 spoke alloys?
Nigel
Anybody want a set of well kerbed 16" 6 spoke alloys?
Nigel
Nigel May
Somerset & Dorset Regional Rep, Membership Secretary, Registrar & Archivist
Email: somerset.dorset@mgfregister.org members@mgfregister.org
MGCC Members register here: https://mgfregister.org/?page_id=319
Somerset & Dorset Regional Rep, Membership Secretary, Registrar & Archivist
Email: somerset.dorset@mgfregister.org members@mgfregister.org
MGCC Members register here: https://mgfregister.org/?page_id=319
- colintf
- Committee Member & Regional Rep
- Posts: 12489
- Joined: Thu Oct 04, 2007 5:49 pm
- MGF Register Region: Devon & Cornwall
- Model of Car: MG PA TF160 ZTV8
- Location: Bristol / Cornwall (back home!)
- Contact:
Re: Did some jobs on the TF today.
god they look good Nigel!nigelandjo wrote:Well not on the TF, but I did take the F to the local tyre fitting centre to have new wheels fitted:
Anybody want a set of well kerbed 16" 6 spoke alloys?
Nigel
Colin Murrell
MGF Register International Liaison Rep
MGF Register Regional Rep for Devon & Cornwall and Cotswold Regions
MGCC Z and V8 Registers Reps for V8 ZT'/ZTTs
http://www.two-sixties.com/main.htm http://www.triple-mracing.com/
- HollieTF
- Posts: 109
- Joined: Wed Oct 10, 2007 5:56 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: TF135,StreetwiseSETD
- Location: Wincanton, Somerset
Re: Did some jobs on the TF today.
Looking good Nigel!! I'm sure Paul will be interested in the old wheels!
Life's too short not to!!!
- nigelandjo
- Committee Member & Regional Rep
- Posts: 4915
- Joined: Tue Oct 09, 2007 9:44 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: TF85th,TF135,Trophy
- Location: Berrow
- Contact:
Re: Did some jobs on the TF today.
I had a feeling that he might be! Let me know, otherwise they will be going on eBay!HollieTF wrote:Looking good Nigel!! I'm sure Paul will be interested in the old wheels!
Nigel
Nigel May
Somerset & Dorset Regional Rep, Membership Secretary, Registrar & Archivist
Email: somerset.dorset@mgfregister.org members@mgfregister.org
MGCC Members register here: https://mgfregister.org/?page_id=319
Somerset & Dorset Regional Rep, Membership Secretary, Registrar & Archivist
Email: somerset.dorset@mgfregister.org members@mgfregister.org
MGCC Members register here: https://mgfregister.org/?page_id=319
- HollieTF
- Posts: 109
- Joined: Wed Oct 10, 2007 5:56 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: TF135,StreetwiseSETD
- Location: Wincanton, Somerset
Re: Did some jobs on the TF today.
I will get Paul to PM you!!nigelandjo wrote:I had a feeling that he might be! Let me know, otherwise they will be going on eBay!HollieTF wrote:Looking good Nigel!! I'm sure Paul will be interested in the old wheels!
Nigel
Life's too short not to!!!
- stux99
- Posts: 2614
- Joined: Mon Oct 08, 2007 5:18 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: TF/TF Steppy/MGGS/3
- Location: Somerset/Dorset border
Re: Did some jobs on the TF today.
Nice work Nigel. Looking good
- nellyandjoo
- Posts: 789
- Joined: Mon Oct 08, 2007 9:27 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: MGTF 135
- Location: Bower Hinton
- James Curgenven
- Posts: 1695
- Joined: Wed Sep 26, 2007 9:45 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: MG ZT 260 SE #455
- Location: Minehead
- Contact:
Re: Did some jobs on the TF today.
Replaced my cooling fan on the ZT today with a Kenlowe replacement, so hopefully that'll be it for cooling now!
Darn site cheaper than a 2 speed OEM one too and just as easy to fit.
Darn site cheaper than a 2 speed OEM one too and just as easy to fit.
- stux99
- Posts: 2614
- Joined: Mon Oct 08, 2007 5:18 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: TF/TF Steppy/MGGS/3
- Location: Somerset/Dorset border
Re: Did some jobs on the TF today.
Mine was the 3 speed and I had to do the wiring mod to get 2 speeds back, suppose I will have to replace it at some stage although I do have a set of bushes to repair it properly
James Curgenven wrote:Replaced my cooling fan on the ZT today with a Kenlowe replacement, so hopefully that'll be it for cooling now!
Darn site cheaper than a 2 speed OEM one too and just as easy to fit.
- James Curgenven
- Posts: 1695
- Joined: Wed Sep 26, 2007 9:45 pm
- MGF Register Region: Somerset & Dorset
- Model of Car: MG ZT 260 SE #455
- Location: Minehead
- Contact:
Re: Did some jobs on the TF today.
£129 for a modified to be a direct fit Kenlowe which should outlast the car from Jules on the 75 & ZT OC site.
- hilly
- Posts: 167
- Joined: Wed Feb 03, 2010 9:43 am
- MGF Register Region: Somerset & Dorset
- Model of Car: Aug 96 MGF VVC Mk1
- Location: Shaftesbury, Dorset
Re: Did some jobs on the TF today.
Looking good Nigel!
Did the 16" wheels go?
If not, any chance of some pictures?
where are you bassed mate?
Dave.
Did the 16" wheels go?
If not, any chance of some pictures?
where are you bassed mate?
Dave.
Why do I always get out of my 'F' with a smile on my face !