ABS controller pinout needed
Moderator: Committee Members
Forum rules
Not many rules really, this board being aimed at technical issues, it shouldn't fall foul (hopefully) of some of the more personal issues that can affect forums.
Rule 1 - Is that you need to think very carefully before posting anything technical or asking anything technical relating to the security system of the car - See 'Security Issues' sticky for more info.
Rule 2 - We (MGF Register) do not support copyright infringement and therefore references to CD ROM, PDF versions or paper copies of the workshop manual (for instance) should not be posted on the forum. We don't want to get into trouble and we'd rather sell you a genuine hard copy through our Regalia shop anyway!
Because advice is honestly and freely given in this technical section, much of it will be amateur experienced based, so any information is given in good faith and is not guaranteed as correct.
Not many rules really, this board being aimed at technical issues, it shouldn't fall foul (hopefully) of some of the more personal issues that can affect forums.
Rule 1 - Is that you need to think very carefully before posting anything technical or asking anything technical relating to the security system of the car - See 'Security Issues' sticky for more info.
Rule 2 - We (MGF Register) do not support copyright infringement and therefore references to CD ROM, PDF versions or paper copies of the workshop manual (for instance) should not be posted on the forum. We don't want to get into trouble and we'd rather sell you a genuine hard copy through our Regalia shop anyway!
Because advice is honestly and freely given in this technical section, much of it will be amateur experienced based, so any information is given in good faith and is not guaranteed as correct.
ABS controller pinout needed
Hi
I bought a Rover 25 ABS controller on ebay as I need something on the bench to test my diagnostic protocol.
I am guessing that it will be the same as the MGF as the protocol certainly is, and I found this wiring diagram
http://mgfcar.de/schedules/sb15.jpg
The problem is that the pins on the controller connector are not numbered so I don't know which one is which.
Has anyone got a diagram on the connector on the ABS controller?
thanks, Philip
I bought a Rover 25 ABS controller on ebay as I need something on the bench to test my diagnostic protocol.
I am guessing that it will be the same as the MGF as the protocol certainly is, and I found this wiring diagram
http://mgfcar.de/schedules/sb15.jpg
The problem is that the pins on the controller connector are not numbered so I don't know which one is which.
Has anyone got a diagram on the connector on the ABS controller?
thanks, Philip
- Rob Bell
- Committee Member
- Posts: 14422
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: ABS controller pinout needed
On the ABS connector shown in that diagram, you'll see that each pin has an alpha-numeric code along the lines of "C6-10". C6 is the connector, and the number, in this example, "10" is the pin.
I am at work at the moment, but I should have a spare ABS controller somewhere.
PS Early MGFs use Bosch 5.0 as you know - whereas later ones (and TFs) use 5.3 - which I suspect may be the version you've got off eBay?
I am at work at the moment, but I should have a spare ABS controller somewhere.
PS Early MGFs use Bosch 5.0 as you know - whereas later ones (and TFs) use 5.3 - which I suspect may be the version you've got off eBay?
- Rob Bell
- Committee Member
- Posts: 14422
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: ABS controller pinout needed
PS - is this what you need?
Re: ABS controller pinout needed
It is exactly what I need. Thanks Rob
Rob Bell wrote:PS - is this what you need?
Re: ABS controller pinout needed
There is now a software update for pscan which makes the ABS 5.0/5.3 protocol work again.
- talkingcars
- Posts: 5766
- Joined: Tue Mar 09, 2010 10:44 pm
- MGF Register Region: South East
- Model of Car: mk1 VVC
- Location: West Sussex
- Contact:
Re: ABS controller pinout needed
I think the pin numbers are on the other side of the socket, under the cover.
Home to black Alfa 159 3.2 V6 Q4, blue MGZR160, green MGF VVC and grey MGF 1.8i, and red MG Maestro T16.
MGF chatting on the Register and at http://www.the-t-bar.com
MGF chatting on the Register and at http://www.the-t-bar.com
- Rob Bell
- Committee Member
- Posts: 14422
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: ABS controller pinout needed
I'll check this ASAP!pscan.eu wrote:There is now a software update for pscan which makes the ABS 5.0/5.3 protocol work again.
-
- Posts: 7
- Joined: Tue Aug 21, 2012 10:45 am
- MGF Register Region: South East
Re: ABS controller pinout needed
But can PScan make the ABS go through its operating sequence, I.e power the relay , valves and pump to assist in brake bleeding ?