bulkhead flex under braking
Moderator: Committee Members
Forum rules
Not many rules really, this board being aimed at technical issues, it shouldn't fall foul (hopefully) of some of the more personal issues that can affect forums.
Rule 1 - Is that you need to think very carefully before posting anything technical or asking anything technical relating to the security system of the car - See 'Security Issues' sticky for more info.
Rule 2 - We (MGF Register) do not support copyright infringement and therefore references to CD ROM, PDF versions or paper copies of the workshop manual (for instance) should not be posted on the forum. We don't want to get into trouble and we'd rather sell you a genuine hard copy through our Regalia shop anyway!
Because advice is honestly and freely given in this technical section, much of it will be amateur experienced based, so any information is given in good faith and is not guaranteed as correct.
Not many rules really, this board being aimed at technical issues, it shouldn't fall foul (hopefully) of some of the more personal issues that can affect forums.
Rule 1 - Is that you need to think very carefully before posting anything technical or asking anything technical relating to the security system of the car - See 'Security Issues' sticky for more info.
Rule 2 - We (MGF Register) do not support copyright infringement and therefore references to CD ROM, PDF versions or paper copies of the workshop manual (for instance) should not be posted on the forum. We don't want to get into trouble and we'd rather sell you a genuine hard copy through our Regalia shop anyway!
Because advice is honestly and freely given in this technical section, much of it will be amateur experienced based, so any information is given in good faith and is not guaranteed as correct.
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
bulkhead flex under braking
I've been doing some research for Project Shed - I am determined to try and rid the car of the slightly spongy and feel-free brake pedal that all MGF and TF suffer from - the original pictures here: http://mgf.ultimatemg.com/group2/common ... _servo.htm
On the above page you'll see some of the things I've been going through trying to get a decent pedal feel. What the page doesn't show is that I have, on my other MGF, relocated the brake master cylinder to the driver's side such that there is a slightly more direct operation between the brake pedal and the master cylinder.
Even that hasn't resolved the problem completely...
I haven't done this on Project Shed, but I have fitted the "Jaylad" bracket to the servo master cylinder support bracket. It gives a useful improvement by triangulating the master cylinder to the top of the bulkhead.
However, this - like all the other solutions I've tried - has not elicited a complete 100% cure.
A couple of animated gifs - anyone like to spot the problems?
On the above page you'll see some of the things I've been going through trying to get a decent pedal feel. What the page doesn't show is that I have, on my other MGF, relocated the brake master cylinder to the driver's side such that there is a slightly more direct operation between the brake pedal and the master cylinder.
Even that hasn't resolved the problem completely...
I haven't done this on Project Shed, but I have fitted the "Jaylad" bracket to the servo master cylinder support bracket. It gives a useful improvement by triangulating the master cylinder to the top of the bulkhead.
However, this - like all the other solutions I've tried - has not elicited a complete 100% cure.
A couple of animated gifs - anyone like to spot the problems?
- talkingcars
- Posts: 5766
- Joined: Tue Mar 09, 2010 10:44 pm
- MGF Register Region: South East
- Model of Car: mk1 VVC
- Location: West Sussex
- Contact:
Re: bulkhead flex under braking
It looks like the whole bulkhead is twisting!Rob Bell wrote:....A couple of animated gifs - anyone like to spot the problems
Home to black Alfa 159 3.2 V6 Q4, blue MGZR160, green MGF VVC and grey MGF 1.8i, and red MG Maestro T16.
MGF chatting on the Register and at http://www.the-t-bar.com
MGF chatting on the Register and at http://www.the-t-bar.com
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: bulkhead flex under braking
Exactly. Both sides and the whole scuttle panel.
Unfortunately it appears that the whole structure is underengineered.
It needs some bacing adding...
Unfortunately it appears that the whole structure is underengineered.
It needs some bacing adding...
- daz
- Posts: 968
- Joined: Wed Aug 21, 2013 5:58 pm
- MGF Register Region: Midlands
- Model of Car: mg less :(
- Location: Birmingham
Re: bulkhead flex under braking
just a thought, have you tried bracing where the heater inlet is?
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: bulkhead flex under braking
I do have a cunning plan!
To provide some context, I took these pictures in the same way as I did with the previous series of images: no brake pedal pressure versus a full heft on the pedal - mimicking what you or I might do for an emergency stop. The bulkhead (hopefully) doesn't move that much under normal road conditions.
I took the pictures to try and visualize and confirm what I thought was going on in respect to the force and reactions.
The brake operation is a little more complicated than perhaps it needs to be. The brake pedal has a link that goes to the transfer torque tube across the bulkhead. The vector of movement is upward and forward. The top of drivers bulkhead therefore moves backward and upward, seemingly rotating on a pivot that appears to the front edge of the bulkhead/scuttle, as the torque tube mount on the lower part of the driver's bulkhead is moving outward and upward.
The rotating torque tube then actuates the master cylinder in the same vector movement - upward and outward. Consequently, the master cylinder/servo assembly downward and forwards, tugging the bulkhead behind with it.
Bracing the servo bracket down to the subframe below did improve the situation:
But still not a complete win.
Daz, you're right, the bulkhead behind the heater does need some kind of support/bracing. Easy on my race car, as I have removed the heater. Harder to do on a road car: the heater is in the way.
My cunning plan?
I want to take out weight anyway, so the plan is to do away with the cross tube completely, and get the master cylinder operated from the brake pedal directly. If my measurements are correct, this may be a little easier than you might think...
Also, relocating to the drivers side is beneficial, because:
1. you can keep the force couple contained within one structure
2. the heater aperture is actually also the pedal box aperture, and this is also triangulated to the pivot of the brake pedal itself - and a major reason why this part of the bulk head doesn't move anything like as much as the other side.
But even this won't completely cure the movement. My idea at the moment is to try and contain the forward movement by tying the brake assembly to the cross bar behind the dash, and any upward movement to the "transmission" tunnel (more of a longitudinal strengthener on the MGF, in which the brake cables and heater pipes run).
I may see whether I can contain the movement of the existing arrangement as a proof of principle - more soon!
To provide some context, I took these pictures in the same way as I did with the previous series of images: no brake pedal pressure versus a full heft on the pedal - mimicking what you or I might do for an emergency stop. The bulkhead (hopefully) doesn't move that much under normal road conditions.
I took the pictures to try and visualize and confirm what I thought was going on in respect to the force and reactions.
The brake operation is a little more complicated than perhaps it needs to be. The brake pedal has a link that goes to the transfer torque tube across the bulkhead. The vector of movement is upward and forward. The top of drivers bulkhead therefore moves backward and upward, seemingly rotating on a pivot that appears to the front edge of the bulkhead/scuttle, as the torque tube mount on the lower part of the driver's bulkhead is moving outward and upward.
The rotating torque tube then actuates the master cylinder in the same vector movement - upward and outward. Consequently, the master cylinder/servo assembly downward and forwards, tugging the bulkhead behind with it.
Bracing the servo bracket down to the subframe below did improve the situation:
But still not a complete win.
Daz, you're right, the bulkhead behind the heater does need some kind of support/bracing. Easy on my race car, as I have removed the heater. Harder to do on a road car: the heater is in the way.
My cunning plan?
I want to take out weight anyway, so the plan is to do away with the cross tube completely, and get the master cylinder operated from the brake pedal directly. If my measurements are correct, this may be a little easier than you might think...
Also, relocating to the drivers side is beneficial, because:
1. you can keep the force couple contained within one structure
2. the heater aperture is actually also the pedal box aperture, and this is also triangulated to the pivot of the brake pedal itself - and a major reason why this part of the bulk head doesn't move anything like as much as the other side.
But even this won't completely cure the movement. My idea at the moment is to try and contain the forward movement by tying the brake assembly to the cross bar behind the dash, and any upward movement to the "transmission" tunnel (more of a longitudinal strengthener on the MGF, in which the brake cables and heater pipes run).
I may see whether I can contain the movement of the existing arrangement as a proof of principle - more soon!
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: bulkhead flex under braking
Here's a picture of the pedal box. Interestingly, there is a captive nut on the left side pedal support bracket. This could prove serendipitous for bracing the pedal box and master cylinder on the driver's side
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: bulkhead flex under braking
Not the best picture to show you what I'm on about: will take more pictures to illustrate!
-
- Posts: 459
- Joined: Wed Oct 28, 2015 9:07 am
- MGF Register Region: Yorkshire
Re: bulkhead flex under braking
What are you using to cover the hole where the air intake for the heater used to be, it looks like a fabric?
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: bulkhead flex under braking
Well, I have some sheet alloy to cover that up, but so far it has been covered up with a different lightweight material.
Gaffer tape.
Will be sorted properly over the winter
-
- Posts: 459
- Joined: Wed Oct 28, 2015 9:07 am
- MGF Register Region: Yorkshire
Re: bulkhead flex under braking
That might be the cause of the flex, ally sheet bonded and riveted is the way forward.Rob Bell wrote:
Well, I have some sheet alloy to cover that up, but so far it has been covered up with a different lightweight material.
Gaffer tape.
Will be sorted properly over the winter
-
- Posts: 97
- Joined: Tue Apr 18, 2017 12:23 pm
- MGF Register Region: South Coast
- Model of Car: MGF VVC & MG ZS T16
- Location: South East
Re: bulkhead flex under braking
The hole is there in all cars though? So shouldn't flex like that.flyingbanana wrote:That might be the cause of the flex, ally sheet bonded and riveted is the way forward.Rob Bell wrote:
Well, I have some sheet alloy to cover that up, but so far it has been covered up with a different lightweight material.
Gaffer tape.
Will be sorted properly over the winter
Although, maybe a couple of Bracing bars corner to corner on the hole would help?
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: bulkhead flex under braking
That's correct - all cars with a heater fitted will have that hole. And even with an alloy plate, the whole structure will move... It is not supported in the correct planes to prevent flex.ZSx wrote:The hole is there in all cars though? So shouldn't flex like that.flyingbanana wrote:That might be the cause of the flex, ally sheet bonded and riveted is the way forward.Rob Bell wrote:
Well, I have some sheet alloy to cover that up, but so far it has been covered up with a different lightweight material.
Gaffer tape.
Will be sorted properly over the winter
Although, maybe a couple of Bracing bars corner to corner on the hole would help?
- talkingcars
- Posts: 5766
- Joined: Tue Mar 09, 2010 10:44 pm
- MGF Register Region: South East
- Model of Car: mk1 VVC
- Location: West Sussex
- Contact:
Re: bulkhead flex under braking
It would be interested to see the same pictures/gifs for a TF with the improved under dash brace and strengthened screen surround.
Home to black Alfa 159 3.2 V6 Q4, blue MGZR160, green MGF VVC and grey MGF 1.8i, and red MG Maestro T16.
MGF chatting on the Register and at http://www.the-t-bar.com
MGF chatting on the Register and at http://www.the-t-bar.com
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: bulkhead flex under braking
I agree, that would be interesting! My hunch would be that the fundamental problems probably still remain, but the TFs I've driven generally have had a better pedal action. There again, the TFs I've driven have generally been pretty new!
Re: bulkhead flex under braking
by coincidence--ive just ordered a servo brace this afternoon.
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: bulkhead flex under braking
The B&G side one? It helps - but actually the "Jaylad" style upper support is superior. Oddly I have yet to try the combination...
- Larry Nicoll
- Posts: 41
- Joined: Tue Jan 19, 2016 12:54 pm
- MGF Register Region: South East
- Model of Car: MG TF
- Location: North Surrey
Re: bulkhead flex under braking
I was unable to obtain the jaylad brace a year or so back so I bought a similar bracket from MG Mania.
MGTF : 2005; 15" wheels; 280mm discs all round; servo brace; Mike Satur gear change; Mike Satur 4:2:1 manifold; sports cat; Daytona silencer; KMaps remap
- Rob Bell
- Committee Member
- Posts: 14431
- Joined: Tue Oct 02, 2007 2:36 pm
- MGF Register Region: South East
- Model of Car: MGF 1.8i + MGF Shed!
Re: bulkhead flex under braking
It's the same - very simple to fabricate yourself and will give you a worth while improvement. Better still it is designed for the snorkel style air inlet that your TF is hopefully already fitted with?
- John SS
- Posts: 493
- Joined: Thu Nov 28, 2013 4:05 pm
- MGF Register Region: Midlands
- Model of Car: 2000 MGF VVC
- Location: Calver Derbyshire
Re: bulkhead flex under braking
This was my solution which has worked well
viewtopic.php?f=8&t=17459
viewtopic.php?f=8&t=17459
- Larry Nicoll
- Posts: 41
- Joined: Tue Jan 19, 2016 12:54 pm
- MGF Register Region: South East
- Model of Car: MG TF
- Location: North Surrey
Re: bulkhead flex under braking
Rob, yes it is that type of air inlet, a very easy fit.
That together with 280mm discs all round provides much improved braking.
That together with 280mm discs all round provides much improved braking.
MGTF : 2005; 15" wheels; 280mm discs all round; servo brace; Mike Satur gear change; Mike Satur 4:2:1 manifold; sports cat; Daytona silencer; KMaps remap