Hydragas Ride Height

http://www.ukmgparts.com
Ask the Gurus - Use this board to discuss problems or technical issues you have with your MGF/TF - there's always an expert around to help you!

Moderator: Committee Members

Forum rules
Not many rules really, this board being aimed at technical issues, it shouldn't fall foul (hopefully) of some of the more personal issues that can affect forums.

Rule 1 - Is that you need to think very carefully before posting anything technical or asking anything technical relating to the security system of the car - See 'Security Issues' sticky for more info.

Rule 2 - We (MGF Register) do not support copyright infringement and therefore references to CD ROM, PDF versions or paper copies of the workshop manual (for instance) should not be posted on the forum. We don't want to get into trouble and we'd rather sell you a genuine hard copy through our Regalia shop anyway! :)

Because advice is honestly and freely given in this technical section, much of it will be amateur experienced based, so any information is given in good faith and is not guaranteed as correct.
Post Reply
User avatar
Phoenix
Posts: 24
Joined: Fri Oct 12, 2007 11:05 pm
MGF Register Region: North West
Model of Car: '98 MGF VVC

Hydragas Ride Height

Post by Phoenix » Tue Dec 04, 2007 4:07 pm

Does anybody know the ideal height that MGFs should ride at? Mine is pretty damn low and needs to be pumped up. It measures 12" from the wheel centre to the wheel arch. I've seen some really high ones and they look ridiculous. Any ideas?

Mr bennett
Posts: 66
Joined: Sun Nov 18, 2007 3:27 pm
MGF Register Region: Midlands
Model of Car: 98 vvc
Location: halesowen west midlands

Re: Hydragas Ride Height

Post by Mr bennett » Tue Dec 04, 2007 4:16 pm

345mm from the hub centre is perfect.
just done mine, cost a tenner.i stayed will the chap and told when to stop when he was pumpin her up. but remember to have 4 wheel trakkin done as well , your f will handle like a dream.
let us know how you get on

User avatar
adrianclifford
Posts: 8007
Joined: Mon Oct 01, 2007 6:56 pm
MGF Register Region: Essex
Model of Car: MGTF 80LE
Location: Leigh on Sea

Re: Hydragas Ride Height

Post by adrianclifford » Tue Dec 04, 2007 5:24 pm

345 is perfect for a Trophy.

Measure from the centre of the hub cap to the underside of the wheel arch, front wheel only, however an F should be 368 =/-10mm.

But as you say, this is not ideal for some people (I think it looks too high) but those are the figures. You will get approximately three fingers between the tyre and the wheel arch, don't forget, F's at this time of the year sit lower than they do in the summer.
Bilstein shocks, Piper 4-2-1 manifold, Daytona, Vader cold-air induction, custom Z and F Stage 2 re-map, Electric boot release, braided hoses, Blue Magnecor leads, Technozen relays, Stage 1 head, BMW Angel Eyes headlights, "MG" puddle lights.

Mr bennett
Posts: 66
Joined: Sun Nov 18, 2007 3:27 pm
MGF Register Region: Midlands
Model of Car: 98 vvc
Location: halesowen west midlands

Re: Hydragas Ride Height

Post by Mr bennett » Tue Dec 04, 2007 7:11 pm

too ade, true they are the figures .. but pumpin her up to 368 now she will look like a 4x4 by the time summer comes. any 1 else got any ideas on this ?????

User avatar
adrianclifford
Posts: 8007
Joined: Mon Oct 01, 2007 6:56 pm
MGF Register Region: Essex
Model of Car: MGTF 80LE
Location: Leigh on Sea

Re: Hydragas Ride Height

Post by adrianclifford » Wed Dec 05, 2007 12:49 pm

The fitting of lowering knuckles will allow you to drop the suspension to what most people thinks looks better (about 345) while still maintaining about 400psi of pressure.

Once again make sure you have a four wheel alignment carried out after.
Bilstein shocks, Piper 4-2-1 manifold, Daytona, Vader cold-air induction, custom Z and F Stage 2 re-map, Electric boot release, braided hoses, Blue Magnecor leads, Technozen relays, Stage 1 head, BMW Angel Eyes headlights, "MG" puddle lights.

User avatar
Kasper
Posts: 711
Joined: Mon Oct 08, 2007 8:24 pm
MGF Register Region: Europe
Model of Car: MGF vvc
Location: Veghel / The Netherlands

Re: Hydragas Ride Height

Post by Kasper » Wed Dec 05, 2007 2:58 pm

adrianclifford wrote:The fitting of lowering knuckles will allow you to drop the suspension to what most people thinks looks better (about 345) while still maintaining about 400psi of pressure.

Once again make sure you have a four wheel alignment carried out after.
Using Lowering pins or as Adrian mentions Knuckles will absolutely give a better view of your car. totally skipping the 4x4 view.
Most important: the ride with pins or knuckles will result in a higher pressure in the hydragas system, so the car will perform better suspension wise and ride feeling. Allthough the car sits lower, it is stiffer and will not collide with speed humps. (at least less then you would expect)

adusting to a lower ride hight is not too expensive 4 pins will cost you about 65 ponds max, and 1,5-2 hours fitting. (wheel alignment more than strongly advised)
MGFvvc - 90FVBG - charcoal - you might think it is original - (1996 nr:8204)
MGTF 120 - 57RNJ7 - BRG - every day is an MG day - (2005)
MGC CGT - SJ08DY - tartan red - 1985 restauration fairly original - (1968 nr: 4137)


http://www.MGF.be

Andrew Regens
Regional Rep
Posts: 742
Joined: Mon Oct 01, 2007 12:10 am
MGF Register Region: Eastern Australia
Model of Car: TF160LE80th #15/1600
Location: Melbourne, Australia

Re: Hydragas Ride Height

Post by Andrew Regens » Thu Dec 06, 2007 6:45 am

I have the lowering knuckles and height set at 345mm or two fingers. I have had it lower and when it gets cold it drops to much so this is the best soloution for every day use. Speed humps I have to take very slowly, as the shocks are very stiff. REMBER to get a 4 wheel alignment.
Piper 4-2-1 Manifold, Daytona Back Box, Stage two Remap, Bilstein Shocks, thicker anti roll bars, PG 1 gearbox Caged bearing with type B Ltd Slip Diff. Large rear brake Kit, Toyo R888R Track/road tyres. Half Roll Cage, 4Point Harness.

User avatar
Pete
Posts: 22
Joined: Thu Oct 11, 2007 12:49 pm
MGF Register Region: South Midlands
Model of Car: MGF VVC '96

Re: Hydragas Ride Height

Post by Pete » Thu Dec 06, 2007 2:16 pm

I visited the technical forum to ask a question about ride height and saw this thread...

I bought my '98 F VVC about six months ago and have always thought it was too low. It looks great but is hitting the ground all the time. I can only get over speed bumps at an absolute crawl. When I arrive at work my passenger has to get out so I can clear the speed bump in our car park. I dread to think what the floor of my car must look like....

I measured the front height from the centre of the hub to the wheel arch and it is not much over 300mm. There is no "finger clearance", the top of the tyre is at best in line with the wheel arch....

I'm not even remotely mechanically minded so could someone explain in layman's terms what options I have? Looking at pictures of it when I bought it it is actually much lower now.... HELP!

Mr bennett
Posts: 66
Joined: Sun Nov 18, 2007 3:27 pm
MGF Register Region: Midlands
Model of Car: 98 vvc
Location: halesowen west midlands

Re: Hydragas Ride Height

Post by Mr bennett » Thu Dec 06, 2007 4:44 pm

pete
just pop into your local garage and ask if they have a hydrogas pump. tell them its for an MGF (which normally baffels the grease monkeys) so tell them it DOES have hydrogas!! i went to 3 garages and non of them belived me until i showed them.
anyway here are the details
http://www.mgf.ultimatemg.com/group2/DI ... r.htm#with

one mechanic even slagged my car of infront of me and the idiot dint even know what suspention it had.pillock :lol: :lol:

Andrew Regens
Regional Rep
Posts: 742
Joined: Mon Oct 01, 2007 12:10 am
MGF Register Region: Eastern Australia
Model of Car: TF160LE80th #15/1600
Location: Melbourne, Australia

Re: Hydragas Ride Height

Post by Andrew Regens » Fri Dec 07, 2007 2:12 am

Pete, the workshop I use specialise in old minis so they can handle the F.
Piper 4-2-1 Manifold, Daytona Back Box, Stage two Remap, Bilstein Shocks, thicker anti roll bars, PG 1 gearbox Caged bearing with type B Ltd Slip Diff. Large rear brake Kit, Toyo R888R Track/road tyres. Half Roll Cage, 4Point Harness.

ErikB
Regional Rep
Posts: 544
Joined: Fri Oct 12, 2007 11:12 am
MGF Register Region: Europe
Model of Car: MGF PTP RT-Sport 165
Location: Belgium
Contact:

Re: Hydragas Ride Height

Post by ErikB » Mon Dec 10, 2007 12:32 pm

@Pete: it may look all right, but the suspension (or better: hydragas spheres) will suffer big time. The sphere (every wheel has its own) has two compartiments: one filled with a nitrogen gas and sealed, the other is filled with a liquid. Using a hydragas pump will add fluid and pressure to the system. Front left and rear left are connected to each other, just like front right and rear right.
Having the system on the correct pressure keeps a nice balance between the pressures of both parts (gas and liquid) and the weigth of the car and forces by the working suspension while driving.
Get it pumped up, before it gets broken.

User avatar
Pete
Posts: 22
Joined: Thu Oct 11, 2007 12:49 pm
MGF Register Region: South Midlands
Model of Car: MGF VVC '96

Re: Hydragas Ride Height

Post by Pete » Fri Dec 14, 2007 8:34 am

Thanks for all the advice, I've found somewhere that will pump it up this weekend. Given that it's freezing cold at the moment what height would you get a 98 F set to? I don't want it to look like a Land Rover come the warmer weather.

(Suspension is bog standard and I don't have the cash at the moment to lower it or modify it in anyway).

User avatar
David Clelland
Posts: 590
Joined: Sun Sep 30, 2007 4:51 pm
MGF Register Region: Scotland
Model of Car: 2001 MGF Steptronic
Location: Kilsyth, Central Scotland
Contact:

Re: Hydragas Ride Height

Post by David Clelland » Fri Dec 14, 2007 10:16 am

Pete wrote:Thanks for all the advice, I've found somewhere that will pump it up this weekend. Given that it's freezing cold at the moment what height would you get a 98 F set to? I don't want it to look like a Land Rover come the warmer weather.

(Suspension is bog standard and I don't have the cash at the moment to lower it or modify it in anyway).
It should be 368mm +/- 10mm from the centre of the front wheel to the underside of the wheel arch at 17°C. If my memory serves me right, you allow 0.4mm for every degree difference in temperature. So, if the weather is colder the distance is less. Remember to leave your car sitting for a while (book recommends 1 hour) to allow the suspension fluid to cool down to ambient temperature. Pressure should be around 400psi but it's the measurement that's the important thing.

Post Reply