Rolling Road and Z&F MEMS3 re-tune Day?

[Keith Williams]

Hi Keith, I'm unable to register as Jersey or the Channel Islands are not recognised, so cannot make the deposit for the RR gang.

What do I do?

I've been in touch with Mark re payment on the day. No problems there.

I'm all booked up to come over from Jersey.

willyphixitt

You have a PM & email Bill. The email will give you a quick fix around the issue. A slot is booked for you on the rolling road, we just need the deposit via a more direct route as suggested in the email, and we will correct the issue of non Channel Islands on our shop when we can.

[Keith Williams]

Rob help !
I have a 2003 TF135 is that a mems 3 ?
Do the deposits cover just having a remap ?
Sorry to be a pain

As far as I know your TF is OK for a remap.
The deposits are only for the rolling road part of the day. All remaps need to be organised and paid for direct with Mark at Z&F.

[willyphixitt]

Hi Keith,

Thanks for your help. I've sent the deposit via the method you suggested. All done and dusted.

Looking forward to the day and meeting like-minded petrolheads.

Regards.

willyphixitt

[MaddAussie]

Arrrgh I may have to drop out... I will be moving that weekend...

[Hainsie]

Sorry guys, I'm going to have to give this a miss due to a family commitment

[Rob Bell]

No worries - hopefully will see many of you there! In fact, I still need to pay my deposit, and I had better do this sharpish or else I'll miss out!!!

[MaddAussie]

Rob

I cant go as I'm moving into a new place you can use my deposit

Mark

[Rob Bell]

Really sorry to hear you can't make it Mark! Hopefully atch up at Silverstone?

[MaddAussie]

Really sorry to hear you can't make it Mark! Hopefully atch up at Silverstone?

I will be on my way to Le Mans mate

[Martin C]

Hi Rob,

What time are we kicking off on Saturday? It is about an hour and half drive for me so need to know what time to set the alarm for.

[BooBoo]

As much as I wanted to go to this I'm going to have to bale out....the clutch on my car isnt too healthy , MJS at Worthing will be having a look on Friday

[Rob Bell]

I'll confirm with Bernie, but I reckon on a kick off time of around 10.

I'll get the list of participants off Keith, but we're rapidly approaching the day (THIS SATURDAY!!!!) so do get in touch and get deposits paid ASAP

Can't wait: it's not often one can get the car RR tested, remapped and then retested!!!

Project Shed still not registered, but if I can find a trailer in time, I might still bring it

See you all soon!

[Rob Bell]

Karl, hope that your car has a nice, simple, easy fix! Keep us posted...

[willyphixitt]

Looking forward to the trip. I hope Condor don't pull a fast one and cancel the Friday sailing. I will be very p**sed off if they do. They've been having engine troubles again on the fast ferries.

Rob -I'll bring a heater fan ecu over with me for you to see. Not had much time re the writing up a self-build article.

Stopping in Southampton on the Friday night and will leave around 7.00am and have brekky en route.

Bill and Jacqueline Nixson

[nigelandjo]

I'm afraid we're going to have to pull out. The Metro's not up to a long trip yet, although (fingers crossed) I've resolved the starting issues ~ new starter, coil and relay fitted, but haven't had chance to test it on a trip longer than a few miles so far.

[Rob Bell]

No worries Bill - and fingers crossed for the ferry! Look forward to seeing the ECU - a very nice bit of tech that

Nigel - good to hear that you've made great progress with the Metro! Sorry not to see it though Hopefully soon? They've become rare beasts all of a sudden

I'll get the attendance list updated. I think we'll have some spare slots for anyone who is interested but not yet signed up. I shall probably need to open this up to other forums...

[Rob Bell]

Hi Chaps,

Mark will be along at 11.00, the RR will start from 09.30-10.00 although Bernie will be there from earlier in the morning, so if you turn up early, Bernie has promised to put the kettle on for a decent brew!

Starting from an earlier "interested" list:

1. Rob - MGF Lotus135 cams, 4-2-1 manifold MEMS1.9 (Project Shed)
2. Hainsie - MGF 1.8i - MEMS1.9
3. Adrian - TF80LE MEMS3 - already remapped by Mark
4. MaddAussie - TF160 - MEMS3 - ?retune
5. Stuart - TF160 - MEMS3 - retune
6. Nigel - MG Metro 1300 - it's got carbs and a distributer mate!
7. c5aliveKarl - TF135 - MEMS3 - ?retune
8. MaddAussie's mate - something noisy, and probably powered by petrol.
9. Paul (Bigfootmgf) - MGF 1.8i - MEMS1.9
10. Martin C - MGF VVC - MEMS2J
11. Colin - TF160 - MEMS3 - retune
12. Ian - MY2000 MGF VVC - MEMS3 - retune
13. AndyWatson - MGF ?engine/management

The list so far for those who've paid up deposits:
1. Andy Watson
2. Paul Bridgman
3. Mark Catterall
4. Martin Charles
5. Stuart Selfe
6. Ian Fleming
7. Bill Nixson
8. Cliff Sutcliff
9. Rob Bell MGF 1.8i MEMS1.9

Only one remap organized for Bill so far - I thought there would be more? I'm a bit worried now that we'll have poor Mark down without sufficient work for him to justify his time

Let me know to update the list - I'll be opening up the day to other forums from now

[Ian007]

Rob

I'm for a remap from Mark - do I need to contact him direct.

Cheers

Ian - see you all saturday

[stuart]

Rob

I'm up for a remap- apologies I presumed that cash on the day would suffice???

[Keith Williams]

I'm for a remap from Mark - do I need to contact him direct.

Payment will be direct to Mark. Just needed to know how many were needed on the day. Cash on the day will be fine. If you want another payment method, please contact Mark direct.

I'm up for a remap- apologies I presumed that cash on the day would suffice???

Cash on the day will be fine for Mark but he/we just needed to know how many were required on the day.

remaps required:
Bill
Ian
Stuart

I am sure Rob will update the lists when he is next on.